(BH098A)  BELLHOUSING TO BOLT TOYOTA CELICA GEARBOXES UP TO CHEV V8 & HOLDEN V8 ENGINE

(BH098A) BELLHOUSING TO BOLT TOYOTA CELICA GEARBOXES UP TO CHEV V8 & HOLDEN V8 ENGINE

(BH102)  BELLHOUSING TO BOLT DYNA AND COASTER 4 & 5 SPPED GEARBOXES UP TO HOLDEN V6 ENGINES

(BH102) BELLHOUSING TO BOLT DYNA AND COASTER 4 & 5 SPPED GEARBOXES UP TO HOLDEN V6 ENGINES

(BH099) BELLHOUSING TO BOLT TOYOTA SUPRA GEARBOXES UP TO CHEV & HOLDEN V8 ENGINES

BELLHOUSING TO BOLT TOYOTA SUPRA TO CHEV AND HOLDEN V8.

  • BELLHOUSING TO BOLT TOYOTA  G51 OR G52 HILUX 5SPD TO CHEV AND HOLDEN V8 
  • KIT THIS BELLHOUSING KIT SUITS HOLDEN TRIMATIC PATTERN V8 ENGINES ANDHOLDEN TURBO PATTERN V8 ENGINES
  • CHEVROLET SMALL BLOCK V8 283-350ci 
  • BELLHOUSING DESIGNED TO WORK WITH TOYOTA Hydraulic clutch set up 
  • BH099KIT BELLHOUSING inc SPIGOT BUSH, PIVOT BALL
  • BH099FULLKIT 
  • KIT INC : PB01
  • BOLT KIT
  • SB10B SPIGOT BUSH
  • TF02 THROWOUT FORK-HYDRAULIC
  • DUST24 DUST COVER
  • PR01 ADJUSTABLE PUSH ROD
  • PRANUT01 PUSH ROD ADJUSTING NUT
  • SPRING01 RETURN SPRING
  • TB06 THRUST BEARING
  • CP02 CLUTCH PLATE 9 1/4 in OR CP03 CLUTCH PLATE 10 in 
  • CB07 THROTTLE CABLE ADAPTOR
  • BEDTHOUSING THERMOSTAT HOUSING (if required)
$650.00
SKU
BH099-CHEV
or 4 interest-free payments of $162.50
Learn more

BELLHOUSING TO BOLT TOYOTA SUPRA TO CHEV AND HOLDEN V8.

  • BELLHOUSING TO BOLT TOYOTA  G51 OR G52 HILUX 5SPD TO CHEV AND HOLDEN V8 
  • KIT THIS BELLHOUSING KIT SUITS HOLDEN TRIMATIC PATTERN V8 ENGINES ANDHOLDEN TURBO PATTERN V8 ENGINES
  • CHEVROLET SMALL BLOCK V8 283-350ci 
  • BELLHOUSING DESIGNED TO WORK WITH TOYOTA Hydraulic clutch set up 
  • BH099KIT BELLHOUSING inc SPIGOT BUSH, PIVOT BALL  
  • BH099FULLKIT  
  • KIT INC : PB01
  • BOLT KIT
  • SB10B SPIGOT BUSH
  • TF02 THROWOUT FORK-HYDRAULIC
  • DUST24 DUST COVER
  • PR01 ADJUSTABLE PUSH ROD
  • PRANUT01 PUSH ROD ADJUSTING NUT
  • SPRING01 RETURN SPRING
  • TB06 THRUST BEARING
  • CP02 CLUTCH PLATE 9 1/4 in OR CP03 CLUTCH PLATE 10 in 
  • CB07 THROTTLE CABLE ADAPTOR
  • BEDTHOUSING THERMOSTAT HOUSING (if required)


    ADDITIONAL INFORMATION    
             
      TIPS:  Use a diesel radiator, use a fan shroud, install diesel diff if changing as    
      they have a higher ratio better suited to the V8.    
             
      These are basic instructions only and things may vary from model to model.     
      We have found two types of engine chassis mounts, one that sits further    
      forward than the others, these seem to be in the following sequence 3 & 4Y series    
      (2 piece type) and 2L & 18R series (1 piece type.)      
      The Toyota rubbers are used in both cases.  In models where the mounts are    
      further back the supplied plate is bolted to the chassis mount facing towards    
      the front of vehicle, the rubbers are then bolted onto the extension plate.    
      If your model has the slave cylinder  on the left hand side, you will need to get    
      a cylinder from any Toyota with a right hand mounted cylinder with the    
      smallest possible bore.  The bore size of 5/8th” is ideal and most brake suppliers    
      could sleeve a cylinder to this size.    
             
      A Commodore sump and oil pickup fits OK.  If your Hilux has power steering or    
      air conditioning be sure to get a motor with all these items attached as it’s just    
      a matter of new hydraulic lines, but if you have to try and adapt the Hilux pumps it    
      is getting to be a major job.    
             
      CRS can supply a special thermostat neck that allows standard radiator hoses to fit.   
      Use Commodore accelerator cable with the supplied bracket which will fit both ends    
      for easy hook up.  The top hand brake cable bracket will foul motor but can be swung    
      out of the way or bolted back on the inside of the vehicle.
     
More Information
Part Type BELL HOUSING
Write Your Own Review
Only registered users can write reviews. Please Sign in or create an account